Measurement-computing Daq PC-Card Instrukcja Użytkownika Pobierz pdf (Strona 16)

1-8 DaqBoard [ISA Type] Quick Start Guide

01-11-00

457-0942, rev 1.2

JP7

–

Calibration

Leave JP7 in default position. Only use JP7 during calibration.

See user’s manual

JP8 –

DMA and Interrupt

Interrupt Selection

. DaqBoard may be set to interrupt the PC when certain hardware conditions occur. The interrupt may

be set to IRQ level 10, 11, 12, 14 or 15. DaqBoard’s IRQ level cannot be shared with another device. To disable interrupt

assistance and background transfers you can configure JP8 to “Open Interrupt” (see following figure).

DMA Selection

. Direct Memory Access (DMA) configuration provides for:

(a)

high-speed data transfer from the ADC FIFO, or

(b)

high-speed data transfer to the DAC FIFO.

Only DMA channels 5-7 (of an ISA AT machine’s seven channels) are available to DaqBoard.

Set DRQ and DACK jumpers to the desired DMA channels. Note that DaqBoard does not share DMA channels.

Set the DMA jumpers to OPEN when other devices will be using DMA channels 5, 6 and 7.

SW1

- Base Address

SW1’s factory default is 300 Hex. If 300 Hex presents an address conflict, set a new SW1 address within the range of

1FF to 3FF (256 to 1023 Decimal). Note that the address must be on a 4-byte boundary.

(2) Make Board Connections

Before connecting your DaqBoard, you should review the following connector descriptions.

P1 Analog I/O

. Provides 16 analog input channels, 2 analog output channels, a 16-bit counter/timer, 4 TTL inputs and

outputs, and various signals for driving expansion cards.

P2 Digital I/O

. Provides three 8-bit TTL programmable I/O ports and external interrupt input. To ensure reliable

operation, for P2 expansion cables

do not exceed 14 inches per attached DBK card

P3 Frequency I/O

. Provides five 16-bit counters and 16 high-speed digital inputs and external interrupt input.

Industry Standard I/O Addresses

Hex Range Device Hex Range Device

000-1FF Internal system 368-36B PC network (high address)

200-207 Game I/O 36C-36F Reserved

20C-20D Reserved 378-37F Parallel printer port 1

21F Reserved 380-38F SDLC, bisynchronous 2

278-27F Parallel printer port 2 390-393 Reserved

2B0-2DF Alternate enhanced graphics adapter 3A0-3AF Bisynchronous 1

2E1 GPIB (Adapter 0) 3B0-3BF Monochrome display and printer adapter

2E2 & 2E3 Data acquisition (Adapter 0) 3C0-3CF Enhanced graphics adapter

2F8-2FF Serial port 2 3D0-3DF Color/Graphics monitor adapter

300-31F Prototype card 3F0-3F7 Diskette Controller

360-363 PC network (low address) 3F8-3FF Serial port 1

364-367 Reserved

Notes:

(1) SW1’s address must be unique, i.e., not used by another device.

(2) I/O addresses, hex 000 to 0FF, are reserved for system board I/O.

(3) Hex 100 to 3FF are available on the I/O channel.

(4) Although the above table represents industry standards, some systems may vary.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 61 62

Komentarze do niniejszej Instrukcji

Brak uwag

Measurement-computing Daq PC-Card Instrukcja Użytkownika Strona 16

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Sprzęt komputerowy Measurement-computing Daq PC-Card