Measurement-computing Personal488 rev.3.0 For DOS & Windows 3.Xi Instrukcja Użytkownika Strona 319
- Strona / 400
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
15A. Driver488/DRV Commands III. COMMAND REFERENCES - 15. Command References
III-304 Personal488 User’s Manual, Rev. 3.0
Bus Addresses Specified
SYNTAX
REMOTE addr[,addr...]
addr
is a device address (primary with optional secondary) or an external device
name.
RESPONSE
None
MODE
SC
•
CA
BUS STATES
REN, ATN
•
UNL, MTA, LAG
SEE ALSO
LOCAL, LOCAL LOCKOUT, Remote (Sub-Chapter 15B)
EXAMPLES
PRINT#1,"REMOTE16,28"
Assert REN and address devices 16 and 28 to
listen.
The
REMOTE
command asserts the Remote Enable (
REN
) bus management line. If the optional bus
addresses are specified,
REMOTE
also address those devices to listen, placing them in the
Remote
state.
REMOVE DEVICE
SYNTAX
REMOVE DEVICE [[,]name...]
name
is the external device to remove.
RESPONSE
None
MODE
Any
BUS STATES
None
SEE ALSO
MAKE DEVICE, KEEP DEVICE, REMOVE DOS NAME
EXAMPLES
PRINT#1, “REMOVE DEVICE DMM”
The
REMOVE DEVICE
command removes the specific temporary or permanent Driver488 device that
was created with either the
MAKE DEVICE
command or the
INSTALL
program. This command also
removes a device that was made permanent through a
KEEP DEVICE
command. Notice that
REMOVE
DEVICE
cannot be used to remove devices having DOS names. The
REMOVE DOS NAME
command
must first be used to remove any associated DOS names from such devices before the devices are
removed via the
REMOVE DEVICE
command.
REMOVE DOS NAME
SYNTAX
REMOVE DOS NAME dosname
dosname
is the name of the Driver488 DOS device to remove.
RESPONSE
None
MODE
Any
BUS STATES
None
SEE ALSO
MAKE DOS NAME, KEEP DOS NAME, REMOVE DEVICE
EXAMPLES
PRINT#1, “REMOVE DOS NAME METER”
The
REMOVE DOS NAME
command removes the temporary or permanent Driver488 DOS device that
was created by either the
MAKE DOS NAME
command or the
INSTALL
program.
REQUEST
SYNTAX
REQUEST[;] status
status is the service
REQUEST
status in the range
0
to
255
.
RESPONSE
None
MODE
*CA
BUS STATES
SRQ if rsv is set
*SRQ if rsv is not set
SEE ALSO
STATUS, CONTROL LINE, PPOLL CONFIG
- Personal488 1
- PC/IEEE 488 Controller 15
- About this Manual 15
- How to Use this Manual 15
- Section I: 17
- I. HARDWARE GUIDES 19
- IEEE 488.2 Interface Boards 20
- Driver488 Software Interface 20
- IEEE 488.1-1987 Interface 22
- IEEE 488.2-1987 Interface 22
- GP488B Interface Board 22
- AT488 Interface Board 22
- MP488 Interface Board 22
- MP488CT Interface Board 23
- GP488/2 Interface Board 23
- GP488/MM Interface Board 23
- NB488 Interface Module 23
- PCMCIA Interface Card 23
- The Package 24
- Default Settings 25
- I/O Base Address Selection 25
- Interrupt Selection 26
- DMA Channel Selection 26
- Wait State Configuration 27
- Internal Clock Selection 27
- Board Installation 27
- 3. Personal488/AT 29
- 4. Personal488/NB 33
- 5. Personal488/MM 34
- 6. Personal488/CARD 38
- Interfaces & Connectors 39
- Interface Cable Connection 39
- Software Installation 40
- Initialization Software 41
- Configuration Software 43
- Functionality 45
- Section II: 47
- II. SOFTWARE GUIDES 49
- 8. Driver488/DRV 50
- Driver Installation to Disk 53
- Multiple Interface Management 60
- DOS Devices 62
- Direct I/O with DOS Devices 63
- 8D. Getting Started 65
- Keyboard Controller Program 66
- 8E. Microsoft C 69
- functions, respectively 73
- return the 16-bit 75
- desired. Here, the 75
- 8G. QuickBASIC 80
- 8H. Turbo C 87
- Initialization of the System 88
- 8I. Turbo Pascal 98
- Configuration of the 195 DMM 100
- Taking Readings 101
- Buffer Transfers 101
- Interrupt Handling 102
- Sample Program 104
- 8J. Spreadsheets 106
- 8K. Other Languages 111
- Finding Addresses 112
- Garbage Collection 113
- Memory Models 113
- Calling Protocols 114
- IOCTL Read & Write 116
- ;DS:DX - command 117
- ;DS:DX-name 118
- ;DS:DX -> command 119
- Use of Direct DOS I/O Devices 121
- BASIC VARPTR & SADDR 121
- JPI TopSpeed Modula-2 122
- Logitech Modula-2 122
- , the segment address of 123
- 8M. Data Transfers 124
- TERM Terminators 128
- Direct I/O & Buffered I/O 129
- , and the 130
- 8N. Operating Modes 131
- Introduction 132
- Operating Mode Transitions 132
- System Controller Mode 133
- Not System Controller Mode 135
- 8O. Utility Programs 136
- Removal & Reinstallation 138
- PRNTEMUL Files 139
- Response 143
- Bus States 143
- Data Types 147
- CCL Reserved Words 148
- 9. Driver488/SUB 149
- Before You Get Started 150
- Making Backup Disk Copies 151
- Driver Installation 151
- Configuration Utility 151
- Interfaces 152
- External Devices 152
- Subroutine Calls 158
- Use of External Devices 159
- Duplicate Device Names 160
- Access of Multiple Interfaces 160
- 9D. Getting Started 161
- Required Libraries 162
- Required Headers 162
- QuickBASIC 164
- Required Definition File 165
- 9E. C Languages 166
- Establishing Communications 167
- Confirming Communication 168
- Setting Up Event Handling 168
- Reading Driver Status 168
- Basic Data Acquisition 170
- Block Data Acquisition 170
- Command Summary 174
- 9F. QuickBASIC 175
- Confirming Communications 176
- 9G. Pascal 182
- 9H. Data Transfers 191
- Data Input and Output 192
- 9I. Operating Modes 193
- 9J. Utility Programs 198
- Running PRNTEMUL 201
- Status Structure 206
- Miscellaneous Constants 206
- Completion Code Bit Masks 206
- 10. Driver488/W31 207
- Enhanced Mode DMA Transfers 210
- NBTEST.EXE 214
- Driver Core Sections 216
- 10D. Getting Started 221
- C Languages 222
- Visual Basic 223
- 10E. C Languages 224
- IEEE 488 Event Message 227
- Sample Programs 232
- Header File (Example2.h) 239
- Header File (Example3.h) 246
- 10F. Visual Basic 248
- Hello Message Window 249
- IEEE 488 Event Custom Control 251
- Data read from the ADC488 253
- Driver488/W31 Status Display 256
- Dynamic Data Exchange (DDE) 257
- Acquisition Engine 259
- Source Code 265
- GLOBAL.BAS Declarations 266
- Handle Lists 268
- WINTEST Session 269
- QUIKTEST 270
- Operation of the Application 271
- Licensing 272
- 11. Driver488/W95 273
- 12. Driver488/WNT 274
- Section III: 275
- COMMAND REFERENCES 275
- 13. Overview 277
- Sub-Chapters 278
- Function Descriptions 278
- The Commands 280
- Syntax Parameters 280
- Defined Constants 281
- Structure Definitions 281
- AUTO REMOTE 300
- BUFFERED 300
- BUS ADDRESS 300
- CHECK LISTENER 301
- CLOCK FREQUENCY 301
- CONTROL LINE 302
- DMA CHANNEL 303
- ENTER (Controller Mode) 303
- ENTER (Peripheral Mode) 304
- FIND LISTENERS 308
- INT LEVEL 309
- IO ADDRESS 309
- IOCTL (BASIC Statement) 310
- IOCTL$ (BASIC Statement) 310
- KEEP DEVICE 311
- KEEP DOS NAME 311
- LIGHT PEN 312
- LOCAL LOCKOUT or LOL 312
- MAKE DEVICE 313
- MAKE DOS NAME 313
- OUTPUT (Controller Mode) 313
- OUTPUT (Peripheral Mode) 314
- PASS CONTROL 317
- PPOLL CONFIG or PPC 317
- PPOLL DISABLE or PPD 318
- PPOLL UNCONFIG or PPU 318
- REMOVE DEVICE 319
- REMOVE DOS NAME 319
- SPOLL LIST 323
- SYS CONTROLLER 325
- TIME OUT 326
- README.TXT 328
- AutoRemote 330
- Buffered 330
- BusAddress 331
- CheckListener 331
- ClearList 332
- ClockFrequency 332
- ControlLine 333
- DmaChannel 335
- Enter (Controller Mode) 335
- Additional Enter Functions 336
- EnterMore 336
- Enter (Peripheral Mode) 337
- EnterI (Controller Mode) 338
- EnterNMoreI 339
- EnterI (Peripheral Mode) 340
- FindListeners 341
- GetError 342
- GetErrorList 342
- IntLevel 343
- IOAddress 344
- KeepDevice 344
- LightPen 344
- LocalList 345
- MakeDevice 346
- MakeNewDevice 346
- MyListenAddr 347
- MyTalkAddr 347
- OnEventVDM 349
- OpenName 350
- Output (Controller Mode) 350
- Additional Output Functions 351
- OutputMore 351
- Output (Peripheral Mode) 352
- OutputI (Controller Mode) 353
- Additional OutputI Functions 354
- OutputNI 354
- OutputMoreI 354
- OutputNMoreI 354
- OutputI (Peripheral Mode) 355
- PassControl 356
- PPollConfig 356
- PPollDisable 357
- PPollDisableList 357
- PPollUnconfig 357
- RemoteList 358
- RemoveDevice 358
- SendData 360
- SPollList 362
- SysController 364
- TermQuery 365
- TimeOutQuery 366
- TriggerList 367
- UnListen 367
- Section IV: 369
- IV. TROUBLESHOOTING 371
- 18A. Introduction 373
- 18B. Driver488/DRV 373
- 18C. Driver488/SUB 374
- 18D. Driver488/W31 375
- 19. Error Messages 377
- Section V: 383
- V. APPENDIX 385
- ASCII Control Codes (Table 2) 388
- ASCII Character Set (Table 1) 389
- ASCII Character Set (Table 2) 390
- Section VI: 391
- VI. INDEX 393
Powiązane produkty i podręczniki dla Sprzęt komputerowy Measurement-computing Personal488 rev.3.0 For DOS & Windows 3.Xi
(48 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji