Measurement-computing Personal Daq rev.6.0 Instrukcja Użytkownika Strona 109
- Strona / 170
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
19. If your Personal Daq is connected to an expansion module:
- remove the USB cable from the Personal Daq main unit
- if used in your application, remove the external power cable from the Personal Daq main unit
- carefully remove the retaining clips from the Personal Daq modules
- remove the expansion module from the main unit
- if a power adapter was used, reconnect the adapter cable to the Personal Daq main unit
- reconnect the USB cable to Personal Daq main unit
Note: For step 20, it is recommended that you make a simple harness from a DB25 male connector to
avoid damaging Personal Daq’s expansion connector. A properly made harness will also ensure
good pin contact. (See following figure).
20. Connect the multimeter positive lead to pin number 24 and the negative lead to pin number 13
(note the harness in the preceding figure). Measure the reference voltage at Personal Daq’s
expansion port, and note the value for use in the following step.
21. Using the keypad of your PC or laptop, enter the reference value obtained from step 20. Select
“Next.” UserCal now calculates calibration constants and stores them in Personal Daq’s serial
EEPROM. UserCal displays a brief calibration report.
Personal Daq User’s Manual 878395 Calibration 6-5
- User’s Manual 1
- Personal Daq 1
- 491-0901 4
- 1086-0926 4
- 1086-0922 4
- About This Manual 5
- Table of Contents 7
- 5 – Signal Management 8
- 6 - Calibration 8
- Unit Startup 1 9
- Install Software 10
- Install Hardware 10
- Personal Daq User’s Manual 11
- Unit Startup 1-3 11
- 1-4 Unit Startup 12
- Personal Daq User’s Manual 12
- CAUTION 13
- Start Personal DaqView 15
- Configure System 16
- Channel Configuration 17
- Acquisition Configuration 17
- Collect Data 18
- PDAQ.BIN, is as follows: 19
- No Expansion 21
- ---- N/A ---- ---- N/A 21
- Features 22
- Theory of Operation 23
- Optical Isolation 24
- A/D Conversion 24
- Input Ranges 24
- Analog Input Configuration 25
- Automatic Calibration 27
- Thermocouple Measurements 27
- Analog Specifications 30
- Input Voltage Ranges 30
- Thermocouple Accuracy 31
- General Specifications 32
- Optional Accessories 32
- Channel Connection Layouts 33
- Calibration 35
- Hardware Setup 3 37
- PDQ Expansion Modules 38
- USB Hubs and Power Adapters 39
- 3-4 Hardware Setup 40
- Hardware Setup 3-5 41
- 3-6 Hardware Setup 42
- Main Control Window 45
- Pull-Down Menus 46
- Measurement Units 47
- Channel Configuration Window 48
- Common Spreadsheet Columns 49
- (b) for the application in 50
- cell for PD1_A01, typed 51
- Analog Input Spreadsheet 52
- Measurement Duration Column 53
- Resolution and Settling Time 55
- 4-14 Personal DaqView 56
- The Trigger Section 58
- Averaging 58
- Acquisition Parameters 59
- 4-18 Personal DaqView 60
- Why use Auto Rearm? 61
- Disabling Auto Rearm 61
- Meter Toolbars 62
- Meter Pull-Down Menus 63
- Meters Configuration Menu 63
- Configuring a Meter 64
- Bar Graph Meters 66
- Analog Meters 67
- Digital Meters 68
- Chart Display 69
- Toolbar Items 71
- Item Description 72
- 4-34 Personal DaqView 76
- 4-36 Personal DaqView 78
- Chart Setup Wizard 79
- 4-40 Personal DaqView 82
- System Requirements 84
- Installation 84
- First Time Use 84
- Configuration Reference 87
- Auto-Load Function 90
- Real-Time Charting 93
- Data Header 94
- Hints and Tips 95
- Signal Acquisition 100
- Triggering 101
- Signal Modes 102
- System Noise 103
- Input and Source Impedance 104
- Crosstalk 104
- Analog Filtering 104
- Introduction 105
- Required Equipment 106
- Calibration Procedure 106
- 878395 Calibration 6-3 107
- 878395 Calibration 6-5 109
- Radio Frequency Interference 111
- Troubleshooting 112
- Customer Assistance 115
- Appendices 117
- Overview 119
- Data Acquisition Environment 119
- Programming Models 120
- Read 1 sample from multiple 122
- Buffers 125
- Multiple Channel Types 128
- API Commands B 133
- (Does not apply to 161
- Personal Daq/54) 161
- Note: Includes “NE” version 163
- Table 9. API Error Codes 165
- 83h - 131 166
Powiązane produkty i podręczniki dla Sprzęt komputerowy Measurement-computing Personal Daq rev.6.0
(26 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.075 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji