Measurement-computing miniLAB-1008 Instrukcja Użytkownika Strona 13
- Strona / 34
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Chapter 3
Functional Details
Theory of operation - analog input acquisition modes
The miniLAB 1008 can acquire analog input data in three different modes – software paced, continuous scan,
and burst scan.
Software paced mode
In software paced mode, the miniLAB 1008 gathers data in a single acquisition or as a group of single
acquisitions. An analog-to-digital conversion is initiated with a software command, and the single data point
result is returned to the host. This operation may be repeated until the required number of samples is obtained
for the channel (or channels) in use. Software pacing is limited by the 20 mS round-trip requirement of a USB
interrupt-type endpoint operation. This yields a maximum throughput in software paced mode of 50 S/s.
Continuous scan mode
In continuous scan mode, the miniLAB 1008 gathers data in a single-channel or multi-channel sequence. This
sequence converts, transfers, and stores data to a user buffer until the scan is stopped. In this mode, digitized
data is continuously written to an on-board FIFO buffer. This FIFO is serviced in blocks as the data is
transferred from the miniLAB 1008 to the user buffer in the host PC.
The maximum continuous scan rate of 1.2 kS/s is an aggregate rate. The total acquisition rate for all channels
cannot exceed 1.2 kS/s. You can acquire data from one channel at 1.2 kS/s, two channels at 600 S/s and four
channels at 300 S/s. You can start a continuous scan with either a software command or with an external
hardware trigger event.
Burst scan mode
In burst scan mode, the miniLAB 1008 gathers data using the full capacity of its 4 K sample FIFO buffer. You
can initiate a single acquisition sequence of one, two, or four channels by either a software command or an
external hardware trigger. The captured data is then read from the FIFO and transferred to a user buffer in the
host PC.
Since the data is acquired at a rate faster than it can be transferred to the host, burst scans are limited to the
depth of the on-board memory. As with continuous mode, the maximum sampling rate is an aggregate rate.
Consequently, the maximum burst mode rates are 8 kS/s, 4 kS/s and 2 kS/s for one, two and four channels,
respectively.
3-1
- User's Guide 1
- USB-based 2
- Table of Contents 5
- About this User's Guide 7
- Introducing the miniLAB 1008 8
- Software features 9
- Installing the miniLAB 1008 11
- Installing the software 12
- Installing the hardware 12
- Functional Details 13
- External components 14
- Screw terminal wiring 16
- Power terminals 20
- Ground terminals 21
- Calibration terminal 21
- Testing terminal 21
- Counter terminal 21
- Accuracy 22
- Offset=9.77mV 23
- Channel gain queue 24
- Digital connector cabling 25
- The red stripe 26
- Specifications 27
- Analog output 28
- External trigger 29
- -40 to 85 °C 30
- 0 to 90% non-condensing 30
- Mechanical 31
- Main connector and pin out 31
- DB37 connector and pin out 32
- Declaration of Conformity 33
Powiązane produkty i podręczniki dla Sprzęt komputerowy Measurement-computing miniLAB-1008
(24 strony)Radio Shack 31-5021 manuels
Manuels d'utilisation et guides de l'utilisateur pour Récepteurs et amplificateurs Radio Shack 31-5021.
Nous fournissons des manuels en pdf 1 Radio Shack 31-5021 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Komentarze do niniejszej Instrukcji