Measurement-computing DaqBoard 3000USB Series Instrukcja Użytkownika Strona 17
- Strona / 128
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
DaqBoard/3000USB Series Installation Guide
968492 IG-11
WARNING !
Turn off power to all devices connected to the system before making connections.
Electrical shock or damage to equipment can result even under low-voltage
conditions.
CAUTION
The discharge of static electricity can damage some electronic components.
Semiconductor devices are especially susceptible to ESD damage. You should
always handle components carefully, and you should never touch connector pins or
circuit components unless you are following ESD guidelines in an appropriate ESD
controlled area. Such guidelines include the use of properly grounded mats and
wrist straps, ESD bags and cartons, and related procedures.
DaqBoard/3031USB and DaqBoard/3035USB make use of J5 and J6 (two of the four 40-pin headers) for
analog expansion. Pinouts for these and the remaining two headers (J7 and J8) are included in this section.
A pinout for a 4-channel terminal board (TB7) is also included.
68-Pin SCSI 40-Pin Headers (4) 4 Channel TC
Connector (J6, J5, J8, J7) Terminal Board
Locations of Signal Connectors and LEDs
Active LED (top)
Power LED (bottom)
LEDs: DaqBoard/3000USB Series boards have 2 LEDs located just right of the USB2 connector (see
figure). The LEDs function as follows:
Active LED
(Top LED)
This LED is on whenever active USB communication is taking place between the DaqBoard
and the host PC. Note that the Active LED will be on solid during a data acquisition.
Power LED
(Bottom LED)
The “Power” LED blinks during device detection and initialization; then remains on solid as long
as the module has power. If there is insufficient power the LED will go off and a TR-2 [or TR-
2U] power adapter will be needed.
Note that when the board is first powered there will likely be a momentary delay before the
Power LED begins to blink, or come on solid.
- DaqBoard/3000USB Series 1
- 938390 5
- *324401C-01* 7
- Contents 9
- (1) Install Software 10
- 968492 IG-5 11
- 968492 IG-7 13
- How to Mount the TB-101 15
- Scenario 4: Using a DBK215 16
- 68-Pin SCSI Connecter 18
- XAPCR = A/D Pacer Clock I/O 20
- -- X-- = Not Connected 20
- 20
- 968492 IG-15 21
- (3) Start DaqView 22
- (4) Configure the System 23
- (5) Collect Data 24
- Customer Assistance 25
- Device Overviews 1 27
- Block Diagrams 28
- Connections 30
- Product Features 31
- 1-6 Device Overviews 32
- 1-8 Device Overviews 34
- 1-10 Device Overviews 36
- Solution: 37
- Example: 37
- 1-12 Device Overviews 38
- Calibration 39
- Analog Output 39
- 1-14 Device Overviews 40
- Counter Inputs 42
- Timer Outputs 42
- 1-18 Device Overviews 44
- Connections and Pinouts 2 45
- 68-Pin SCSI Connecter (P5) 46
- TB-101 Terminal Board Option 51
- TB-101 Pinouts 52
- Hardware Setups 56
- Scenario 2: Using a TB-100 57
- Scenario 3: Using a DBK215 58
- Safety Conditions 59
- 949290 User’s Manual 60
- Calibration 4 61
- Counter Input Modes 5 63
- Encoder Mode (see page 15) 68
- Counter/Totalize Mode 68
- Period Mode 70
- Pulsewidth Mode 73
- Timing Mode 75
- Encoder Mode 77
- Wiring for 1 Encoder 80
- Criteria 84
- Input Signal is Equal to X 84
- Driven by Condition 84
- Detecting Input Values 85
- See the TIP below 85
- The Setpoint Status Register 93
- DaqBoard/3000USB Series 7 95
- Analog Inputs 96
- AutoZero Disabled 97
- Type T thermocouple 98
- A/D Specifications 99
- Input Sequencer 99
- Triggering 100
- Digital I/O 101
- Pattern Generation Output 102
- Counters 102
- Frequency/Pulse Generators 103
- Software 103
- Accessories and Cables 104
- Dimensions 105
- Overview 107
- DBK215, pg. A-2 108
- 886994 Appendix A 108
- TB16 Supports BNCE thru BNCF 108
- Connection Tips 109
- System Examples 110
- WARNING ! 111
- DBK215, pg. A-6 112
- [2 Screws per-side] 112
- 886994 DBK215 A-7 113
- 886994 DBK215 A-9 115
- 886994 DBK215 A-11 117
- WARNING 118
- CAUTION 118
- 886994 DBK215 A-13 119
- Specifications for DBK215 120
- Signal Modes 121
- 938390 Appendix B 122
- Shielding 123
- TC Common Mode 123
- Analog Filtering 125
- Input and Source Impedance 125
- Crosstalk 125
- Glossary 127
- 887194 Glossary 128
Powiązane produkty i podręczniki dla Sprzęt komputerowy Measurement-computing DaqBoard 3000USB Series
(74 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji